THE PERFECT COMPLEMENT FOR MACHINE CONTROL

Adquio multi IOs modbus module

This module allows you to carry out complete control of your climate machines, exchangers, chillers, evaporator / condenser units, air treatment units, etc. In general, any device that needs controls of all kinds such as relays, digital and analog signals, both input and output.

With this device you will improve your facilities for these reasons:

You don’t need to install a programmable controller to integrate a machine.
The cost of machine integration is divided, since its control is simplified.
You can connect screens, thermostats, etc. directly to this device for manual control of it. (Requires study and programming depending on the case).

Another of its important uses is that we can customize its programming specifically for a specific machine and it can work in a disconnected way without the need for a programmable controller, this is ideal for manufacturers, since by integrating it into their machines, it provides their customers with a fully functional machine. and controllable via modbus RTU, and if desired with a control screen where the end customer can set slogans, view statuses, etc.

Contact Request presentation

CONNECTIONS

Adquio multi IOs modbus module

Front connectors and top indicators

Power connection, 24V DC
Microswitches for modbus address configuration.
485 slave connector with 3 contacts A, B and GND. You use it to control this device from a higher purchase or controller.
485 master connector with 3 contacts A, B and GND. You use them if you want to connect a control display or thermostat directly to this device. (Designed for cases in which this device is used in a pre-programmed way to perform a very specific function, controlling a machine).
4 Inputs that can be used as analog and digital, admit a voltage range from 0 to 24 volts, when read as digital, 1 is assumed when passing 4.7V.
4 pairs of contacts for 4 PT1000 probes.
Error indicator.
Indicator of correct connection with the master.
Power indicator

Front connectors acquire multi IOs modbus module

Rear connectors

10 contacts for 5 dry contact relays with support up to 10A at 250V.
4 0-24V digital outputs with power transistors to drive relays.
4 Inputs that can be used as analog and digital, admit a voltage range from 0 to 24 volts, when read as digital, 1 is assumed when passing 4.8V.
GND connector, ground or negative pole, useful for nearby digital outputs.
4 0-10V analog outputs.

Technical specs

Energy

Power supply
24VDC

Consumption

130mA

Connectivity

Port 485 slave

Compatible with Modbus RTU 9600-19200 bps). It will allow you to connect this device to any controller that supports Modbus RTU, including any of the acquired models.

Port 485 master

It allows you to connect screens or thermostats, for manual and direct control of the parameters of this device.

Inputs

Analog and digital inputs

8 analog or digital inputs configurable by the user according to the needs of the installation.

When they behave as digital you will get a 1 from 4.8 Volts.

When they behave as analog they can work in the range of 0-10V or 0-24V

For 4-20mA inputs use our DIN rail converter.

Outputs

Relay outputs
5 switch relay outputs up to 10A at 250V. High quality and durable relays, more than 100,000 actuations before failure.

Digital outputs

4 24v digital outputs (with power transistors)

Analog outputs

4 0-10V analog outputs

Control

Indicator LEDs
3; Power, Online and Error

PDF Datasheet

Certifications

Safety and Health

EN ISO 13849-1: 2015

EN ISO 13849-2: 2012

EN 62061: 2005 + A1: 2013 + A2: 2015

EN 60950-1: 2006

EN 62311: 2008

EMC

EN 61000-6-4: 2007 + A1: 2011

EN 61000-6-2: 2005

ETSI EN 301 489-1 v2.2.0

ETSI EN 301 489-17 v3.2.0

RoHS

EN 50581: 2012